China Good quality Swl Series Stainless Steel Worm Gear Jacks Linear Manual Car Mechanical Lift Landing Electric Reducer Worm Gear Screw Jack with Best Sales

Product Description

1.Convenient to adjust
2.Wide range of ratio
3.Easy to install
4.high torque
Application Industries:
Our SWL series screw jacks are widely used in the industries such as metallurgy,mining,hoisting and transportation, electrical
power,energy source,constrction and building material,light industry and traffice industry

Screw Jacks in construction

Often found in climbing mechanism of construction,the screw jacks use physical means to raise and lower loads, which typically range from 5 tons to 30 tons. A screw jack is a common type of mechanical jack, which works via a motor and gearbox by an operator. A screw uses the shape of its threads to raise or lower the load, or a traveling nut does the lifting while the screw turns in place. Mechanical jacks are self-locking(not for ball screw), which means that when power is removed from the jack, the screw stays in place until power resumes. This setup makes mechanical jacks safer than their hydraulic counterparts, because users don’t have to fear a loss of power. The main components of screw jacks are; trapezoidal lifting screw also known as lead screw, worm screw, worm gear and gear housing. A worm screw is rotated manually or by a motor. With the rotation of the worm gear, the lead screw in it moves upwards or downwards linearly. The feed rate of the screw depends on the turning speed, the number of teeth of the gears and the size of the screw pitch. In some models of jackscrews, The lifting screw does not move up and down. It only rotates around its axis. A lifting nut (also known as a travelling nut) moves along the lead screw. The lifting nut of the screw jack is made of bronze to decrease friction.

Product Parameters

MODEL

 

SWL2.5

SWL5

SWL10

SWL15

SWL20

SWL25

SWL35

Maximum lifting force (kN)

 

25

50

100

150

200

250

350

Screw thread size

 

Tr30*6

Tr40*7

Tr58*12

Tr58*12

Tr65*12

Tr90*16

Tr100*20

Maximum tension (kN)

 

25

50

99

166

250

350

Worm gear ratio (mm)

P

1/6

1/8

3/23

1/8

3/32

3/32

 

M

1/24

1/24

1/24

1/24

1/32

1/32

Worm non rotating stroke (mm)

P

1.0

0.875

1.565

1.56

1.5

1.875

M

0.250

0.292

0.5

0.5

0.5

0.625

Maximum elongation of screw rod under tensile load (mm)

 

1500

2000

2500

3000

3500

4000

Maximum lifting height at maximum pressure load (mm)

The head of the screw rod is not guided

250

385

500

400

490

850

820

Lead screw head guide

400

770

1000

800

980

1700

1640

Worm torque at full load(N.m)

P

18

39.5

119

179

240

366

464

M

8.86

19.8

60

90

122

217

253

efficiency(%)

P

22

23

20.5

 

19.5

16

18

M

11

11.5

13

 

12.8

9

11

Weight without stroke(kg)

 

7.3

16.2

25

 

36

70.5

87

Weight of screw rod per 100mm(kg)

 

0.45

0.82

1.67

 

2.15

4.15

5.20

Detailed Photos

 

 

 

SWL Series worm screw Jack:

1.The elevator is a combination of turbine pair and trapezoid screw rod to complete the lifting and lowering of objects. 2.Compact structure, light weight, safety and reliability, long service life, convenient installation

3.Self-locking function in the static state.

 

1. screw rod

2. nut bolt

3. cover

4.Skeleton oil seal

5.Bearing

6.Worm gear

7.Oil filling hole

8.Case

9.Skeleton oil seal

10.Cover

11. nut bolt

12.Bearing

13.Skeleton oil seal

14.Bearing

15.worm

16.Flat key

17.Bearing

18.Skeleton oil seal

19.Cover

20.Nut bolt

Product Description

 

Related Products

 

Packaging & Shipping

 

Company Profile

 

Standard or Nonstandard: Nonstandard
Application: Textile Machinery, Garment Machinery, Conveyer Equipment, Electric Cars, Motorcycle, Food Machinery, Marine, Mining Equipment, Agricultural Machinery, Car
Product Name: Swl Series Worm Gear Lift
Input Speed: 0-1440rpm
Ratio: 6-36
Applicable Industries: Hotels, Manufacturing Plant, Food & Beverage Facto
Samples:
US$ 50/Piece
1 Piece(Min.Order)

|
Request Sample

screw gear

How do you install a screw gear system?

Installing a screw gear system, also known as a worm gear system, requires careful consideration and precise execution. Here’s a detailed explanation of the steps involved in installing a screw gear system:

  1. Design and Selection: Before installation, it is crucial to design and select the appropriate screw gear system for the specific application. Consider factors such as required torque, speed, load capacity, gear ratio, and environmental conditions. Choose a screw gear system that matches the application’s requirements and ensure compatibility with other components and machinery.
  2. Prepare the Components: Gather all the necessary components for the screw gear system installation, including the worm gear, worm wheel, bearings, shafts, and any additional accessories or support structures. Inspect the components for any damage or defects and ensure they are clean and properly lubricated.
  3. Mounting the Worm Gear: Begin the installation by mounting the worm gear. Securely attach the worm gear to the appropriate shaft or motor using suitable fasteners. Ensure that the alignment of the worm gear is accurate, and it is properly centered on the shaft to avoid any misalignment issues during operation.
  4. Mounting the Worm Wheel: Once the worm gear is in place, mount the worm wheel. The worm wheel should be positioned in such a way that it meshes smoothly with the worm gear. Ensure that the worm wheel is securely mounted, and any necessary bearings or supports are properly installed to maintain stability and alignment.
  5. Alignment and Adjustment: Proper alignment of the screw gear system is crucial for its efficient operation. Ensure that the worm gear and worm wheel are correctly aligned both axially and radially. Check for any excessive play or binding in the system. Make necessary adjustments to achieve optimal alignment and smooth meshing between the gears.
  6. Lubrication: Apply the recommended lubricant to the screw gear system. Proper lubrication is essential to minimize friction and wear, ensuring smooth operation and extending the system’s lifespan. Follow the manufacturer’s guidelines regarding the type and amount of lubricant to use.
  7. Testing and Fine-Tuning: After installation, perform thorough testing of the screw gear system. Check for smooth operation, proper engagement between the gears, and any abnormal noise or vibration. Fine-tune the system if necessary, making adjustments to achieve the desired performance and ensure optimal functionality.
  8. Regular Inspection and Maintenance: Once the screw gear system is installed and operational, it is important to establish a regular inspection and maintenance schedule. Regularly inspect the system for signs of wear, lubrication levels, and any potential issues. Perform routine maintenance tasks such as cleaning, lubrication replenishment, and component replacement as needed.

It is crucial to follow the manufacturer’s guidelines and specifications during the installation process. If unsure about any aspect of the installation, consult with experts or refer to the manufacturer’s documentation for detailed instructions specific to the screw gear system being installed.

screw gear

How do you address thermal expansion and contraction in a screw gear system?

Addressing thermal expansion and contraction in a screw gear system is crucial to ensure the proper functioning and longevity of the system. Thermal expansion and contraction occur when a system is subjected to temperature changes, leading to dimensional changes in the components. Here’s a detailed explanation of how to address thermal expansion and contraction in a screw gear system:

  1. Material Selection: Choose materials for the screw gear system components that have compatible coefficients of thermal expansion (CTE). Using materials with similar CTE can help minimize the differential expansion and contraction between the components, reducing the potential for misalignment or excessive stress. Consider materials such as steel, bronze, or other alloys that exhibit good dimensional stability over the expected operating temperature range.
  2. Design for Clearance: Incorporate proper clearances and tolerances in the design of the screw gear system to accommodate thermal expansion and contraction. Allow for sufficient clearance between mating components to accommodate the expected dimensional changes due to temperature variations. This can prevent binding, excessive friction, or damage to the gears during temperature fluctuations.
  3. Lubrication: Utilize appropriate lubrication in the screw gear system to mitigate the effects of thermal expansion and contraction. Lubricants can help reduce friction, dissipate heat, and provide a protective film between the mating surfaces. Select lubricants that offer good thermal stability and maintain their properties across the expected temperature range of the system.
  4. Thermal Insulation: Implement thermal insulation measures to minimize the exposure of the screw gear system to rapid temperature changes. Insulating the system from external heat sources or environmental temperature fluctuations can help reduce the thermal stresses and minimize the effects of expansion and contraction. Consider using insulating materials or enclosures to create a more stable temperature environment around the screw gear system.
  5. Temperature Compensation Mechanisms: In certain applications, it may be necessary to incorporate temperature compensation mechanisms into the screw gear system. These mechanisms can actively or passively adjust the position or clearance between components to compensate for thermal expansion or contraction. Examples include thermal expansion compensation screws, bimetallic elements, or other devices that can accommodate dimensional changes and maintain proper alignment under varying temperatures.
  6. Operational Considerations: Take into account the thermal characteristics of the environment and the operational conditions when using a screw gear system. If the system is expected to experience significant temperature variations, ensure that the operating parameters, such as load capacities and operating speeds, are within the design limits of the system under the anticipated temperature range. Monitor and control the temperature of the system if necessary to minimize the effects of thermal expansion and contraction.
  7. System Testing and Analysis: Conduct thorough testing and analysis of the screw gear system under various temperature conditions to assess its performance and behavior. This can involve measuring dimensional changes, analyzing gear meshing characteristics, and evaluating the system’s ability to maintain proper alignment and functionality. Use the test results to validate the design, make any necessary adjustments, and optimize the system’s performance under thermal expansion and contraction effects.
  8. Maintenance and Inspection: Establish a regular maintenance and inspection routine for the screw gear system to monitor its performance and address any issues related to thermal expansion and contraction. This can involve checking clearances, lubrication levels, and the overall condition of the system. Promptly address any signs of excessive wear, misalignment, or abnormal operation that may be attributed to temperature-related effects.

By considering material selection, design clearances, lubrication, thermal insulation, temperature compensation mechanisms, operational considerations, and regular maintenance, it is possible to effectively address thermal expansion and contraction in a screw gear system. These measures help ensure the system’s reliability, minimize wear and damage, and maintain the desired performance and functionality over a range of operating temperatures.

screw gear

What are the benefits of using a screw gear mechanism?

A screw gear mechanism, also known as a worm gear mechanism, offers several benefits that make it suitable for various applications. Here are some of the key advantages of using a screw gear mechanism:

  • High Gear Reduction Ratio: Screw gears provide a high gear reduction ratio, which allows for significant torque multiplication. This means that a small input torque can produce a much larger output torque, making screw gears ideal for applications that require high torque output and low-speed rotation.
  • Precise Positioning: Screw gears offer precise positioning capabilities due to their fine-pitch threads and high gear reduction ratio. This makes them well-suited for applications that require accurate and controlled motion control, such as robotics, automation, and positioning systems.
  • Self-Locking: One of the notable advantages of screw gears is their self-locking property. The friction between the worm and the worm wheel prevents the backdriving of the system when at rest, eliminating the need for additional braking mechanisms or external locks. This self-locking feature is particularly useful in applications where holding a position is crucial, such as elevators, lifts, and safety mechanisms.
  • Compact Design: Screw gear mechanisms have a compact design, making them suitable for applications with limited space. The worm and worm wheel configuration allows for a compact layout, enabling efficient power transmission in tight spaces where other types of gear mechanisms may not be feasible.
  • Quiet Operation: Screw gears typically operate more quietly compared to other gear types. The meshing of the helical threads results in smooth and gradual contact, reducing noise and vibration. This makes screw gear mechanisms desirable in applications where low noise levels are essential, such as in audio equipment, precision instruments, and residential environments.
  • High Shock Load Resistance: Screw gears are known for their ability to withstand shock loads. The helical nature of the threads and the larger contact area between the worm and the worm wheel distribute the load more evenly, reducing the risk of sudden failures or damage due to shock or impact loads.
  • Reliable and Durable: Screw gears are known for their reliability and durability. The simplicity of their design, with fewer moving parts, results in fewer points of failure. Additionally, the self-locking feature reduces the chances of unwanted movement or slippage. When properly lubricated and maintained, screw gear mechanisms can have a long service life and require minimal maintenance.
  • Versatility: Screw gears can be manufactured in various sizes, materials, and configurations to suit different applications. They can be designed as right-handed or left-handed, with different thread pitches and tooth profiles. This versatility allows for customization and adaptability to meet specific application requirements.

These benefits make screw gear mechanisms a popular choice in industries such as manufacturing, automotive, robotics, elevators, and various other applications where high torque, precise positioning, compactness, and reliability are crucial.

China Good quality Swl Series Stainless Steel Worm Gear Jacks Linear Manual Car Mechanical Lift Landing Electric Reducer Worm Gear Screw Jack with Best SalesChina Good quality Swl Series Stainless Steel Worm Gear Jacks Linear Manual Car Mechanical Lift Landing Electric Reducer Worm Gear Screw Jack with Best Sales
editor by CX 2023-09-28

Tags:

Recent Posts

screw-gear

As one of leading screw-gear manufacturers, suppliers and exporters of mechanical products, We offer screw-gear and many other products.

Please contact us for details.

Mail:[email protected]

Manufacturer supplier exporter of bush chains

We specializing in the production of Agricultural Gearbox, PTO Shafts, Sprockets, Fluid Coupling, Worm Gear Reducers, Gears and racks, Roller Chains, Sheave and Pulleys, Planetary Gearboxes, Timing Pulleys, Shaft Collars and more.

We have exported our products to clients around the world and earned a good reputation because of our superior product quality and after-sales service.

We warmly welcome customers both at home and abroad to contact us to negotiate business, exchange information and cooperate with us.