China Custom Fubao 180mm High Load Capacity Slasher Gearbox Speed Reducer Wabseries worm gear motor

Product Description

Product Description

FuBao 180mm high Load Capacity Slasher Gearbox Speed Reducer WABseries

HangZhou Fubao Electromechanical Technology Co., Ltd. slasher gearbox speed reducer is a new generation of practical products independently developed by our company:

Low noise: less than 65db.

Low back clearance: up to 3 arc minutes in a CHINAMFG and 5 arc minutes in a double stage.

High torque: higher than the standard planetary reducer torque.

High stability: high strength alloy steel, the whole gear after hardening treatment, not only the surface hard substitution.

High deceleration ratio: Modular design, planetary gearbox can be interlinked.

slasher gearbox speed reducer characteristic:

1.Planetary reducer manufacturer-Fubao Electromechanical Technology adopts an integrated planetary carrier and output shaft, which can provide better torsional rigidity. After precision machining, the gear set is not easy to eccentric, which can reduce interference, reduce wear and noise, and at the same time use a large The bearings are arranged with a wide span to distribute the load of the bearings, and once again strengthen the torque rigidity and radial load capacity of the slasher gearbox speed reducer. The output cover is made of aluminum alloy, which provides better heat dissipation capability for the product, so that the reducer produced by Fubao Electromechanical Technology can play an excellent role in the field of mechanical tools.

2.The planetary gear set is specially made of alloy steel. First, it undergoes quenching and tempering heat treatment to make the material hardness reach HRC30 degrees, and then undergoes nitriding surface treatment to HV860, so that the product has the characteristics of high surface hardness and high toughness in the center, and achieves the best product strength and service life. optimization.

3.The input shaft and the motor output shaft are connected by a bolted structure, with a round shaft seal design, and through dynamic balance analysis, it can ensure that there is no eccentric load at high speeds. After reducing unnecessary radial force, it can effectively Reduce the load on the motor side.

4.The material of the input cover/motor connection seat is made of aluminum alloy, which can provide better heat dissipation effect, and then provide good concentricity and verticality through professional lathe processing, so that the product can be stably combined with various motors, reducing the damage caused by insufficient precision. Unnecessary axial radial force makes the product have a longer life cycle.

WAB series parameters Model number WAB042 WAB60 WAB090 WAB115 WAB140 WAB180 WAB220
Rated output torque 14-22 23-60 48-160 140-330 342-650 520-1200 1140-2000
Reduction ratio L1: 3, 4, 5, 6, 7, 8, 9, 10    L2: 15, 20, 25, 30, 35, 40, 50, 70, 80, 100
Planetary gear backlash L1: P0≤1 P1≤3 P2≤5   L2: P0≤3 P1≤5 P2≤7

 

Detailed Photos

Product Details

Other products

Product Advantage

Compared with other reduction machines, planetary gear reduction machines have high rigidity, high precision (single stage can be achieved within 1 point), high transmission efficiency (single stage in 97-98%), high torque/volume ratio, lifetime maintenance free and other characteristics.

Because of these characteristics, planetary gear reducer is mostly installed on the stepper motor and servo motor, used to reduce speed, increase torque, matching inertia.

Company Profile

HangZhou Fubao Electromechanical Technology Co., Ltd. was established in 2008, the company has a complete precision reducer design, production capacity. Set R & D, manufacturing, assembly and sales, more in the field of gear manufacturing has more than 10 years of background, in the manufacturing equipment is equipped with Switzerland Riesenhahl gear grinding machine, domestic Qinchuan gear grinding machine, hamai gear hobbing machine and domestic Xihu (West Lake) Dis. gear hobbing machine, Japan Yasaki TLGmazak CNC lathe, CNC milling machine and other fully CNC equipment, In addition, it is equipped with other advanced measuring equipment such as Japanese TTI gear detector, 3 coordinate measurement, reducer backlash measurement instrument and so on. In a strong manufacturing capacity at the same time, can be stable, continuous manufacturing of high-quality precision reducer products.

The precision reducer produced by our company has the characteristics of high structural rigidity, small back backlash, precise transmission and so on. It is widely used in various industries. Companies adhering to the concept of let customers participate in manufacturing, and strive to provide customers with more personalized services. In the field of precision transmission has a unique achievements. It is our CHINAMFG pursuit to make far-reaching contributions.

 

Factory Display

Q: Speed reducer grease replacement time
A: When sealing appropriate amount of grease and running reducer, the standard replacement time is 20000 hours according to the aging condition of the grease. In addition, when the grease is stained or used in the surrounding temperature condition (above 40ºC), please check the aging and fouling of the grease, and specify the replacement time.

Q: Delivery time
A: Fubao has 2000+ production base, daily output of 1000+ units, standard models within 7 days of delivery.

Q: Reducer selection
A: Fubao provides professional product selection guidance, with higher product matching degree, higher cost performance and higher utilization rate.

Q: Application range of reducer
A: Fubao has a professional research and development team, complete category design, can match any stepping motor, servo motor, more accurate matching.

Shipping Cost:

Estimated freight per unit.



To be negotiated
Application: Motor, Machinery, Agricultural Machinery, Ball Screw Drive Shaft
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Customization:
Available

|

Customized Request

screw gear

How do you maintain and service a screw gear system?

Maintaining and servicing a screw gear system, also known as a worm gear system, is essential to ensure its optimal performance, longevity, and reliability. Regular maintenance and proper servicing help identify and address issues before they escalate into major problems. Here’s a detailed explanation of how to maintain and service a screw gear system:

  1. Establish a Maintenance Schedule: Create a maintenance schedule for the screw gear system based on the manufacturer’s recommendations, operating conditions, and the system’s usage. The schedule should include routine inspections, lubrication, cleaning, and any other specific maintenance tasks.
  2. Visual Inspection: Regularly inspect the screw gear system visually. Check for any signs of wear, damage, misalignment, or unusual noise or vibration. Look for oil leaks, loose fasteners, or any other visible issues that may affect the performance of the system.
  3. Lubrication: Ensure that the screw gear system is properly lubricated. Monitor the lubricant level and condition regularly. Follow the manufacturer’s guidelines regarding the type of lubricant to use, the recommended viscosity, and the lubrication intervals. Replenish or replace the lubricant as necessary to maintain optimal lubrication and reduce friction.
  4. Cleaning: Keep the screw gear system clean and free from debris, dirt, or contaminants. Regularly clean the gears, shafts, and other components using appropriate cleaning methods and agents. Be careful not to damage any of the components during the cleaning process.
  5. Alignment Check: Periodically check the alignment of the screw gear system. Misalignment can lead to increased wear, reduced efficiency, and premature failure. Ensure that the worm gear and worm wheel are properly aligned axially and radially. If misalignment is detected, make the necessary adjustments to bring the gears back into proper alignment.
  6. Bearing Maintenance: If the screw gear system includes bearings, inspect and maintain them regularly. Check for any signs of wear, excessive play, or noise. Lubricate the bearings according to the manufacturer’s recommendations. Replace any worn or damaged bearings promptly.
  7. Load and Performance Testing: Periodically perform load and performance testing on the screw gear system. This helps assess its functionality, efficiency, and torque capacity. Analyze the test results and compare them to the system’s specifications. If any deviations or performance issues are identified, take appropriate measures to rectify them.
  8. Component Replacement: Over time, certain components of the screw gear system may wear out and require replacement. Keep a record of the system’s maintenance history and track the lifespan of critical components. Replace worn or damaged gears, bearings, seals, or other components as needed to ensure the system’s reliability and performance.
  9. Documentation: Maintain thorough documentation of all maintenance activities, including inspection reports, lubrication records, component replacements, and any repairs or adjustments made. This documentation helps track the system’s maintenance history, identify recurring issues, and plan future maintenance tasks.

It is important to note that the maintenance and service procedures may vary based on the specific screw gear system, its design, and the manufacturer’s recommendations. Therefore, always refer to the manufacturer’s documentation and guidelines for detailed instructions specific to the screw gear system being serviced.

screw gear

How do you address thermal expansion and contraction in a screw gear system?

Addressing thermal expansion and contraction in a screw gear system is crucial to ensure the proper functioning and longevity of the system. Thermal expansion and contraction occur when a system is subjected to temperature changes, leading to dimensional changes in the components. Here’s a detailed explanation of how to address thermal expansion and contraction in a screw gear system:

  1. Material Selection: Choose materials for the screw gear system components that have compatible coefficients of thermal expansion (CTE). Using materials with similar CTE can help minimize the differential expansion and contraction between the components, reducing the potential for misalignment or excessive stress. Consider materials such as steel, bronze, or other alloys that exhibit good dimensional stability over the expected operating temperature range.
  2. Design for Clearance: Incorporate proper clearances and tolerances in the design of the screw gear system to accommodate thermal expansion and contraction. Allow for sufficient clearance between mating components to accommodate the expected dimensional changes due to temperature variations. This can prevent binding, excessive friction, or damage to the gears during temperature fluctuations.
  3. Lubrication: Utilize appropriate lubrication in the screw gear system to mitigate the effects of thermal expansion and contraction. Lubricants can help reduce friction, dissipate heat, and provide a protective film between the mating surfaces. Select lubricants that offer good thermal stability and maintain their properties across the expected temperature range of the system.
  4. Thermal Insulation: Implement thermal insulation measures to minimize the exposure of the screw gear system to rapid temperature changes. Insulating the system from external heat sources or environmental temperature fluctuations can help reduce the thermal stresses and minimize the effects of expansion and contraction. Consider using insulating materials or enclosures to create a more stable temperature environment around the screw gear system.
  5. Temperature Compensation Mechanisms: In certain applications, it may be necessary to incorporate temperature compensation mechanisms into the screw gear system. These mechanisms can actively or passively adjust the position or clearance between components to compensate for thermal expansion or contraction. Examples include thermal expansion compensation screws, bimetallic elements, or other devices that can accommodate dimensional changes and maintain proper alignment under varying temperatures.
  6. Operational Considerations: Take into account the thermal characteristics of the environment and the operational conditions when using a screw gear system. If the system is expected to experience significant temperature variations, ensure that the operating parameters, such as load capacities and operating speeds, are within the design limits of the system under the anticipated temperature range. Monitor and control the temperature of the system if necessary to minimize the effects of thermal expansion and contraction.
  7. System Testing and Analysis: Conduct thorough testing and analysis of the screw gear system under various temperature conditions to assess its performance and behavior. This can involve measuring dimensional changes, analyzing gear meshing characteristics, and evaluating the system’s ability to maintain proper alignment and functionality. Use the test results to validate the design, make any necessary adjustments, and optimize the system’s performance under thermal expansion and contraction effects.
  8. Maintenance and Inspection: Establish a regular maintenance and inspection routine for the screw gear system to monitor its performance and address any issues related to thermal expansion and contraction. This can involve checking clearances, lubrication levels, and the overall condition of the system. Promptly address any signs of excessive wear, misalignment, or abnormal operation that may be attributed to temperature-related effects.

By considering material selection, design clearances, lubrication, thermal insulation, temperature compensation mechanisms, operational considerations, and regular maintenance, it is possible to effectively address thermal expansion and contraction in a screw gear system. These measures help ensure the system’s reliability, minimize wear and damage, and maintain the desired performance and functionality over a range of operating temperatures.

screw gear

How do you choose the right size screw gear for your application?

Choosing the right size screw gear for your application involves considering several factors to ensure optimal performance and compatibility. Here are the key steps to follow when selecting a screw gear:

  1. Determine the Application Requirements: Start by understanding the specific requirements of your application. Consider factors such as the desired gear reduction ratio, torque requirements, rotational speed, load capacity, and precision positioning needs. Having a clear understanding of your application’s requirements will help guide the selection process.
  2. Calculate the Gear Ratio: Determine the required gear reduction ratio by considering the speed and torque specifications of your application. The gear reduction ratio is calculated by dividing the input speed by the output speed. This ratio will help narrow down the options for suitable screw gears.
  3. Evaluate Load Capacity: Assess the load capacity requirements of your application. Consider the maximum load that the screw gear needs to handle. This includes both the static load (the load when the system is at rest) and the dynamic load (the load during operation). Ensure that the selected screw gear can handle the anticipated loads without experiencing excessive wear or failure.
  4. Consider Torque Requirements: Determine the required torque output of the screw gear to meet the demands of your application. Calculate the torque by multiplying the load torque by the gear reduction ratio. Ensure that the selected screw gear can provide the necessary torque output to drive the load effectively.
  5. Analyze Speed and Efficiency: Evaluate the desired rotational speed and efficiency of the screw gear system. Consider the input speed, output speed, and efficiency requirements of your application. Ensure that the selected screw gear can operate within the desired speed range while maintaining the required efficiency levels.
  6. Check Mounting and Space Constraints: Assess the available space and mounting requirements in your application. Consider factors such as the required size, shape, and mounting configuration of the screw gear. Ensure that the selected screw gear can be properly installed and integrated into your application without any space or mounting constraints.
  7. Consider Material and Lubrication: Evaluate the environmental conditions and operating parameters of your application. Consider factors such as temperature, humidity, exposure to contaminants, and the need for corrosion resistance. Select a screw gear made from materials suitable for the application environment. Additionally, consider the lubrication requirements and ensure that the selected screw gear can be adequately lubricated for smooth operation and reduced wear.
  8. Consult Manufacturers and Suppliers: Seek advice and consult with manufacturers or suppliers of screw gears. They can provide valuable insights and recommendations based on their expertise and product knowledge. Provide them with the specific details of your application requirements for better guidance in selecting the appropriate screw gear.

By following these steps and considering the factors mentioned, you can choose the right size screw gear that matches the requirements of your application. It is crucial to ensure that the selected screw gear can handle the load, provide the necessary torque and speed, fit within the available space, and operate effectively in the application environment.

China Custom Fubao 180mm High Load Capacity Slasher Gearbox Speed Reducer Wabseries worm gear motorChina Custom Fubao 180mm High Load Capacity Slasher Gearbox Speed Reducer Wabseries worm gear motor
editor by CX 2023-09-28

Tags:

Recent Posts

screw-gear

As one of leading screw-gear manufacturers, suppliers and exporters of mechanical products, We offer screw-gear and many other products.

Please contact us for details.

Mail:[email protected]

Manufacturer supplier exporter of bush chains

We specializing in the production of Agricultural Gearbox, PTO Shafts, Sprockets, Fluid Coupling, Worm Gear Reducers, Gears and racks, Roller Chains, Sheave and Pulleys, Planetary Gearboxes, Timing Pulleys, Shaft Collars and more.

We have exported our products to clients around the world and earned a good reputation because of our superior product quality and after-sales service.

We warmly welcome customers both at home and abroad to contact us to negotiate business, exchange information and cooperate with us.